Ceiling Fan Installation & Small Electrical Jobs in Queen Creek & the East Valley

Ceiling fan installed on a vaulted ceiling in a bright Queen Creek, AZ great room, for ceiling fan installation and small electrical jobs

Henderson’s Electric Solutions, an electrical contractor based in Queen Creek, AZ (led by licensed electrician Randy Henderson, ROC CR-11 #341452), installs ceiling fans and handles the small electrical jobs on your list: light fixture swaps, new or replacement outlets, GFCI and USB outlets, switches and dimmers, and patio fans and lighting. We check the box, the bracing, and the circuit, not just the fixture, and we’re glad to group several small jobs into one visit.

Quick Facts

  • Service area: Queen Creek, San Tan Valley, Gilbert, Chandler, Tempe, Scottsdale, Paradise Valley, and the rest of the Phoenix metro East Valley
  • License: Arizona ROC CR-11 #341452, held by licensed electrician Randy Henderson; bonded & insured
  • Hours: Monday to Friday, 6am to 6pm; emergency calls answered 24/7, including nights and weekends
  • Office: (480) 228-3875
  • Randy: (480) 430-2775
  • Permits: Pulled by Henderson’s where required
  • Utility coordination: We schedule SRP and APS disconnects and reconnects when a job calls for one
  • Small jobs: Group your list into one visit: fans, fixtures, outlets, GFCIs, switches, and dimmers

What small electrical jobs do you handle?

These are the jobs homeowners usually put off. Most are quick on their own, and they make the most sense when you group a few together.

  • Ceiling fans: New fans, replacements for old or wobbly fans, and swapping a light fixture for a fan
  • Light fixture swaps: Replacing dated fixtures, vanity lights, and porch lights with the ones you’ve picked out
  • Outlets: Adding outlets where you need them, replacing worn or loose outlets, and updating old two-prong outlets
  • GFCI outlets: Kitchens, bathrooms, garages, laundry areas, and outdoor outlets
  • USB outlets: Outlets with built-in USB-A or USB-C charging for kitchens, nightstands, and desks
  • Switches and dimmers: New switch locations, three-way switches, dimmers, and fan speed controls
  • Outdoor and patio: Wet-rated patio fans, porch and patio lights, and weather-protected outdoor outlets

Planning a full lighting layout, recessed lights, or a remodel? That’s covered on our lighting installation page.

Why does a ceiling fan need a fan-rated box?

A fan is heavier than most light fixtures, and it moves. Every time it spins, it puts a small, constant twist and vibration on whatever it hangs from. A plastic or light-duty box screwed to drywall can loosen over time, and that’s how fans start to wobble or, in the worst case, come down.

  • Fan-rated box: We confirm the box is listed for fan support, or replace it with one that is.
  • Solid mounting: The box is fastened to a ceiling joist or to a fan brace that spans between joists. A brace can usually go in through the existing hole without opening the ceiling.
  • Heavier fans: Large or heavy fans may need support beyond the box, and we follow the manufacturer’s instructions for that.
  • Balanced and tight: We assemble, hang, and balance the fan so it runs quietly at every speed.
Checklist of small electrical jobs in Queen Creek, AZ: ceiling fans, fixtures, outlets and switches, GFCI upgrades, troubleshooting, exterior lights, smoke detectors, breakers

Can you install fans on high or vaulted ceilings?

Yes. Many newer East Valley homes have tall great rooms, vaulted ceilings, and two-story entries, and those fans need a little more planning.

  • Downrods: On a tall ceiling, a longer downrod brings the fan down to where it actually moves air. Fan makers generally call for the blades to be at least 7 feet off the floor and clear of the ceiling.
  • Sloped ceilings: We use a fan and canopy rated for the ceiling angle, with a sloped-ceiling adapter where needed, so the fan hangs straight and doesn’t hit the slope.
  • Hard-to-reach boxes: We bring the ladders and equipment to work safely at height.
  • Controls: High fans are hard to reach, so we’ll suggest a wall control or remote that you’ll actually use.

Adding a fan where there was only a light

Swapping a light for a fan

This is the most common fan job we do. We pull the old fixture, check the box and replace it with a fan-rated box and brace if needed, and confirm the circuit can handle the fan. If you want the fan and the light on separate switches, we check whether the extra wire is already there.

A fan where nothing is now

If the room has no ceiling box at all, we find a nearby circuit with capacity, run new wire through the attic to a fan-rated box, and add a wall switch or control. We’ll walk you through the route before we start, so there are no surprises in the drywall.

Which wall controls work with ceiling fans?

A fan motor needs a control made for fans. A regular light dimmer can make a fan hum, overheat, or fail, so we never use one to slow a fan.

  • Separate fan and light switches: Needs an extra wire between the switch and the fan. We can run it if your home only has one.
  • Fan speed controls: Wall-mounted speed controls built for fan motors, with a matching dimmer for the light kit when the fan has one.
  • Remotes and wall-mount remotes: A good fit for high ceilings or where running new wire isn’t practical.
  • Smart fan controls: Fan controls that work alongside your smart lighting. See our Lutron lighting controls page for whole-home systems.

Where does code call for GFCI outlets?

A GFCI (ground-fault circuit interrupter) shuts power off in a fraction of a second when current leaks to ground, like through water or a person. That’s why the electrical code calls for GFCI protection in places where water is nearby. In general, that includes:

  • Kitchen countertop outlets and outlets near sinks
  • Bathrooms
  • Garages and unfinished spaces
  • Outdoor outlets, including patios and yards
  • Laundry areas

Exact requirements depend on the code edition adopted where you live and when the work is done, and we install to the code that applies. Pressing the TEST and RESET buttons once a month is a quick way to check them. If a GFCI won’t reset, keeps tripping, or a whole row of outlets is dead, our troubleshooting and repair service finds the cause.

Adding or replacing outlets and USB outlets

Need an outlet behind the TV, on the kitchen island, in the garage for a freezer, or by the bed? We add outlets on a circuit that can carry the load, so you aren’t relying on extension cords and power strips. We also replace loose, cracked, or scorched outlets, and swap standard outlets for ones with built-in USB-A or USB-C charging.

Older homes sometimes have two-prong outlets with no ground wire. We’ll explain the code-allowed options, from running a ground to adding GFCI protection. If your panel is out of space or overloaded, a panel upgrade may be the better long-term fix.

Outdoor and patio fans and lighting

Arizona patios get sun, dust, monsoon rain, and misting systems. A fan or fixture rated for indoor use won’t last out there.

  • Damp-rated vs wet-rated: Damp-rated works under a fully covered patio. Wet-rated is the right choice anywhere rain, sprinklers, or misters can reach.
  • Protected circuits: Outdoor outlets get GFCI protection and in-use weather covers.
  • Porch and patio lights: We swap fixtures, add lights on new switches, and help with timers so lights come on when you need them.

Bundle your small jobs into one visit

Small electrical jobs are easier on everyone when they’re grouped. Walk your house, write down everything you’ve been meaning to fix or add, and send us the list. We’ll plan the visit around all of it and come prepared with the right boxes, braces, and devices.

  • Move-ins: fans in the bedrooms, fixture swaps, and dimmers before the furniture arrives
  • Getting ready to sell: replacing dated fixtures, fixing dead outlets, and adding GFCIs where they’re missing
  • Summer prep: patio fans, outdoor outlets, and a fan in the room that never cools down

Sending a photo of each item (the existing fixture, the box, the outlet) with your request helps us plan. Send us your list.


Why choose Henderson’s Electric Solutions?

Done right, not just done

  • Fan-rated boxes and proper bracing on every fan
  • The right control for the job, never a light dimmer on a fan motor
  • Permits pulled where required

Licensed and accountable

  • Led by licensed electrician Randy Henderson, Arizona ROC CR-11 #341452
  • Bonded & insured
  • BBB Accredited since November 2025, rated A+
  • Owned by Randy and Tori Henderson, founded in 2022, based in Queen Creek

Solutions Only - No Excuses

Small jobs get the same care as big ones. Your fan won’t wobble, your outlets will work, and you’ll get a straight answer about what your home needs.


Frequently asked questions

Do I need a special box or brace for a heavy fan or a vaulted ceiling?

Yes. A ceiling fan must hang from a box that is listed for fan support, and the box has to be fastened to framing or a fan brace, not just the drywall. Standard light boxes aren’t built for a fan’s weight and wobble. Heavier fans may need support beyond the box, as the manufacturer specifies. On sloped or vaulted ceilings we also use a fan rated for the angle, a sloped-ceiling adapter, and a downrod long enough to keep the blades clear of the ceiling.

Can you add a ceiling fan to a room that has no ceiling light now?

Usually, yes. We look for a nearby circuit with room to spare, then run new wire to a fan-rated box and a new wall switch. Attic access makes this easier; on a single-story home it’s often a clean job. If there’s no good path for the wire, we’ll explain the options before any drywall is cut.

Can I control the fan and light separately from the wall?

Often. Separate wall control needs an extra wire between the switch and the fan. Many homes that were wired for a single light only have one, so you can either use the fan’s remote for one function or have us run the extra wire. We also install fan speed controls, which must be made for fan motors. A regular light dimmer should never be used to slow a fan.

Which fans and fixtures hold up on an Arizona patio?

Use a fan or fixture with the right rating for where it hangs: damp-rated for fully covered patios, and wet-rated anywhere rain, sprinklers, or misters can reach it. Wet-rated fans handle monsoon storms and misting systems better, and UV-resistant finishes last longer in our sun. Outdoor outlets and circuits also need GFCI protection and weather-resistant covers.

Where do I need GFCI outlets in my home?

In general, the electrical code calls for GFCI protection where water and electricity meet: kitchen countertops, bathrooms, garages, outdoor outlets, laundry areas, and spots near sinks, among others. The exact list depends on the code edition your city or county has adopted and when the work is done. If your outlets aren’t protected or a GFCI won’t reset, we can test them and bring them up to date.

Can you take care of several small electrical jobs in one visit?

Yes, and that’s the best way to book small work. Send us your list, like a fan in the bedroom, a new outlet in the garage, a dimmer in the dining room, and a GFCI by the patio door. We’ll plan the visit around all of it, so everything gets done in one trip instead of several.


Ready to check some jobs off your list?

Tell us about the fan, fixtures, or outlets you have in mind, and add anything else on your list. Call (480) 228-3875, email info@hendersonselectric.com, or request an estimate online. Electrical emergency? Our 24/7 emergency line is the same number.